Search found 543 matches
- Mon Nov 29, 2010 2:17 am
- Forum: General Discussion / Links / Off Topic
- Topic: Hindle headers for exup 1000's
- Replies: 4
- Views: 2879
*Bump!* I have one of these, and though I haven't fitted it yet it looks great. Really must fit it soon and tune the carbs to suit, so I can go track this summer. In fact I'd go fit it now, only the fZ1 is up on blocks with wheels out, 2 punctures in the rear and 1 in the front, so I have no room to...
- Thu Nov 25, 2010 6:26 am
- Forum: Photos of Your Yamaha
- Topic: Merry Christmas and here's a present for the board
- Replies: 9
- Views: 7701
Magazine just published this pic:
in this article
http://www.visordown.com/advanced-ridin ... 15835.html
and I didn't know where else to post it ...
in this article
http://www.visordown.com/advanced-ridin ... 15835.html
and I didn't know where else to post it ...
- Thu Nov 25, 2010 3:28 am
- Forum: General Discussion / Links / Off Topic
- Topic: Rear wheel and engine swaps
- Replies: 8
- Views: 6460
- Mon Nov 22, 2010 5:45 am
- Forum: General Discussion / Links / Off Topic
- Topic: Rear wheel and engine swaps
- Replies: 8
- Views: 6460
- Tue Nov 16, 2010 4:44 am
- Forum: Racing
- Topic: St George last round
- Replies: 18
- Views: 9792
- Thu Nov 11, 2010 5:16 pm
- Forum: Racing
- Topic: Track Day Broadford 30th May
- Replies: 29
- Views: 15790
- Thu Nov 11, 2010 2:45 am
- Forum: Tech Tips
- Topic: Genesis vs Exup blocks??
- Replies: 25
- Views: 17674
- Thu Nov 11, 2010 2:15 am
- Forum: Tech Tips
- Topic: Genesis vs Exup blocks??
- Replies: 25
- Views: 17674
- Wed Nov 10, 2010 4:24 am
- Forum: Tech Tips
- Topic: Genesis vs Exup blocks??
- Replies: 25
- Views: 17674
I'm fairly certain the blocks have the same cylinder center to center spacing Hmm, dunno then. Maybe I'm thinking of carb spacing, but it'd be worth checking before purchase. I know the genesis is narrower in some aspects of the engine, but I've never owned one so it's hard to be certain which and ...
- Wed Nov 10, 2010 3:28 am
- Forum: Tech Tips
- Topic: Genesis vs Exup blocks??
- Replies: 25
- Views: 17674
I'm 99% certain that the cylinder spacing is bigger on the EXUP series blocks. The Genesis blocks get up to 1029 and I think that's the max, whereas the EXUP blocks have enough room and sleeve thickness to get bored up to 1040 without new sleeves, and the block can be bored to accept bigger sleeves,...
- Wed Nov 03, 2010 1:07 am
- Forum: Racing
- Topic: Duke's Taupo raceday
- Replies: 14
- Views: 7904
- Mon Nov 01, 2010 10:28 pm
- Forum: Photos of Your Yamaha
- Topic: More of the old girl
- Replies: 6
- Views: 6470
- Mon Nov 01, 2010 5:07 pm
- Forum: Racing
- Topic: Duke's Taupo raceday
- Replies: 14
- Views: 7904
Oh no, tragic! :hissy At least you have lots of parts lined up ready to go, if you hadn't it would be even more heartbreaking. Still noone likes that to happen. The 1040 pistons have valve pockets milled deeper to account for high lift cams and bumped compression, when you check you might find that ...
- Mon Nov 01, 2010 5:03 pm
- Forum: Photos of Your Yamaha
- Topic: My old girl
- Replies: 15
- Views: 9654
- Sun Oct 31, 2010 1:45 am
- Forum: Racing
- Topic: KIWI's Taupo Race Day
- Replies: 5
- Views: 4677
- Fri Oct 29, 2010 5:35 pm
- Forum: Tech Tips
- Topic: Is it rich or lean???
- Replies: 8
- Views: 7270
Spook - take a trip to Jaycar and build one on the cheap: http://www.jaycar.com.au/products_uploaded/productLarge_14081.jpg EGO (Exhaust Gas Oxygen) Tester Refer: Electronics Australia February 1994 An EGO sensor monitors your engines exhaust and tells the EFI computer if your engine is running lean...
- Fri Oct 29, 2010 4:04 pm
- Forum: Tech Tips
- Topic: Is it rich or lean???
- Replies: 8
- Views: 7270
- Tue Oct 26, 2010 6:48 am
- Forum: General Discussion / Links / Off Topic
- Topic: Tig Welding
- Replies: 13
- Views: 5749
Nice. Can it weld steel as well? How is it with thin sheet/thin tube? I guess you need a gas can with it (argon or nitrogen or something?) I was toying with the idea of an arc welder for general home and bike use, but I would like the ability to weld aluminium as well. Recommendations for an occasio...
- Mon Oct 11, 2010 5:23 am
- Forum: General Discussion / Links / Off Topic
- Topic: A Binary day
- Replies: 5
- Views: 3775
- Thu Sep 30, 2010 5:52 am
- Forum: Racing
- Topic: Cars and Bikes Meeting
- Replies: 20
- Views: 11957